Talkaphone WEBS-RETRO-MT/R4 WEBS Retro Kit for ETP-MT/R OP5 T User Manual download pdf

WEBS-RETRO-MT/R4 Installation Instructions

Talk-A-Phone Co. • 7530 North Natchez Avenue • Niles, Illinois 60714-3804 Rev. 11/24/09

Phone 773.539.1100 • Fax 773.539.1241 • [email protected] • www.talkaphone.com

All prices and specifications are subject to change without notice.

Talk-A-Phone, Talk-A-Lert, Scream Alert and WEBS are registered trademarks of Talk-A-Phone Co.

I. Introduction

The WEBS-RETRO-MT/R4 is a kit that converts an existing ETP-MT/R OP 4 Tower into a WEBS

-capable Mass

Notification Unit. This instructions manual assumes that a fully functional ETP-MT/R OP 4 Tower has already

been installed.

II. Contents

Before beginning the installation, make sure you have all the included components. Each kit consists of three

packages, which include the painted WEBS

Retrofit tower top, the extra long replacement camera arm, and the

following components:

QTY

Part Number

Description

83073

WEBS

Loudspeaker

24651

Amplifier Mounting Bracket

Paging Amplifier

2’ Extension wire for WEBS

loudspeakers

42841

10-24 x 3/4" pan head tamperproof screw

42839

3/4"-10 hex nut

42840

3/4" washer

42847

10-24 Hex nuts for Amplifier Bracket

III. Installation

(A) Replacing the Tower Arm

1) Unplug the strobe light from the power supply and the emergency phone.

2) Unplug the optional CCTV camera from the power supply and all other devices (i.e. emergency

phone, network switch).

3) Remove the cap plate of the ETP-MT/R OP 4 tower top by unfastening three 10-24 x 3/4” pan head

tamperproof screws and keep them safely aside (See Figure 1).

4) Remove the ETP-MT/R4 OP 4 arm from the tower by unfastening four carriage bolts and keep them

safely aside. Pull out all cabling still attached to the strobe light and the optional CCTV camera from

the tower.

5) Take off the strobe light attached to the top of the ETP-MT/R4 OP 4 tower arm along with cabling and

reattach it to the new tower arm using the same screws.

6) Take off the optional CCTV camera attached to the bottom of the ETP-MT/R4 OP 4 tower arm along

with cabling and reattach it to the new tower arm using the same screws.

7) Feed all the cabling through the Cable Opening into the tower and reattach the new tower arm to the

ETP-MT/R OP 4 tower with the four carriage bolts included with the arm.

1 2 3 4 5

Summary of Contents

Page 1

Page 2 - Figure 1. Installing the WEBS

Page 3 - Figure 2. Installing the WEBS

Page 4

Page 5

Comments to this Manuals

No comments

Talkaphone WEBS-RETRO-MT/R4 WEBS Retro Kit for ETP-MT/R OP5 T User Manual

Browse online or download User Manual for Accessories communication Talkaphone WEBS-RETRO-MT/R4 WEBS Retro Kit for ETP-MT/R OP5 T. Talkaphone WEBS-RETRO-MT/R4 WEBS Retro Kit for ETP-MT/R OP5 Tower User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Accessories communication Talkaphone WEBS-RETRO-MT/R4 WEBS Retro Kit for ETP-MT/R OP5 T