Talkaphone WEBS-RETRO-MT/R WEBS Retro Kit for ETP-MT/R Tower User Manual download pdf

WEBS-RETRO-MTR Installation Instructions

Talk-A-Phone Co. • 7530 North Natchez Avenue • Niles, Illinois 60714-3804 Rev. 2/22/10

Phone 773.539.1100 • Fax 773.539.1241 • [email protected] • www.talkaphone.com

All prices and specifications are subject to change without notice.

Talk-A-Phone, Talk-A-Lert, Scream Alert and WEBS are registered trademarks of Talk-A-Phone Co.

I. Introduction

The WEBS-RETRO-MTR is a kit that converts an existing ETP-MT/R Tower to a WEBS

-capable Mass

Notification Unit. This instruction manual assumes that a fully functional ETP-MT/R Tower has already been

installed.

II. Contents

Before beginning installation, make sure you have all the included components. Each kit consists of two

packages. Package #1, labeled WEBS-RETRO-MTR contains the painted WEBS

retrofit tower top. Package

#2, labeled WEBS-RETRO-KIT contains the following:

QTY Part Number Description

4 83073 WEBS

Loudspeaker

24651 Amplifier Mounting Bracket

NA Paging Amplifier

NA 2’ Extension wire for WEBS

loudspeakers

4 42841 10-24 x 3/4" pan head tamperproof screw

2 42839 3/4"-10 hex nut

8 42840 3/4" washer

4 42847 10-24 Hex nuts for Amplifier Bracket

3 42902 10-24 x 1-1/2” pan head phillips screw

III. Installation

(A) Installing the Retrofit Tower Top (figure 1).

1) Remove and discard the cap plate of the ETP-MT/R tower top by unfastening two 10-24 x 3/4” pan

head tamperproof screws.

2) Detach the strobe light from the top of the tower by unfastening the three 10-24 x 3/4" pan head

tamperproof screws (keep the strobe inside the polycarbonate enclosure).

3) Place four WEBS

loudspeakers into the Retrofit Tower Top resting on the bottom and feed the

speaker wiring through the bottom.

4) Raise the Retrofit Tower Top to the top of the tower and pass the WEBS

loudspeakers wiring

through the center hole of the Strobe Mounting Plate and down to the bottom of the tower; attach the

cabling with the wiring clamps to the side of the ETP-MT/R tower’s polycarbonate top.

5) Attach the supplied stand-off bracket to the bottom of the strobe and fasten both to the Strobe

Mounting Plate with three 10-24 x 1-1/2" pan head phillips screws provided.

6) Fasten the Retrofit Tower Top to the top of the tower with the help of the two 10-24 x 3/4" pan head

tamperproof screws provided.

7) Install the four WEBS

loudspeakers in the Retrofit Tower Top by locking each down with the retainer

bracket starting with the bottommost speakers first.

8) Close the top of the retrofit tower top with its cap plate.

1 2 3 4

Figure 1. Installing the WEBS 2

Summary of Contents

Page 1

Page 2 - Figure 1. Installing the WEBS

Page 3

Page 4

Comments to this Manuals

No comments

Talkaphone WEBS-RETRO-MT/R WEBS Retro Kit for ETP-MT/R Tower User Manual

Browse online or download User Manual for Accessories communication Talkaphone WEBS-RETRO-MT/R WEBS Retro Kit for ETP-MT/R Tower. Talkaphone WEBS-RETRO-MT/R WEBS Retro Kit for ETP-MT/R Tower User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Accessories communication Talkaphone WEBS-RETRO-MT/R WEBS Retro Kit for ETP-MT/R Tower